Differences

This shows you the differences between two versions of the page.

--- netzwerk:switches:cisco_nxos [2023/01/05 14:11] – [Timezone & NTP] stone
+++ netzwerk:switches:cisco_nxos [2023/04/03 14:20] (current) – stone
@@ Line 2: / Line 2: @@
 ===== Basic System Config =====
+==== Alias ====
+<code>
+cli alias name wr copy running-config startup-config
+</code>
+\\
 ==== Hostname ====
@@ Line 7: / Line 13: @@
 <code ->
 hostname SuperGeilerSwitch
+ip domain-name mylab.loc
+no ip domain-lookup
+</code>
+\\
+==== Gateway ====
+Default Gateway. \\  Man kann natürlich auch einzelne Routen setzten
+<code ->
+ip route 0.0.0.0/0 10.0.0.1
 </code>
@@ Line 21: / Line 38: @@
 show clock
 </code>
-\\
-\\
+\\  \\
 ==== Banner MOTD ====
@@ Line 36: / Line 53: @@
 #
 </code>
+\\
+==== SNMP ====
+<code>
+snmp-server contact Maurice Moss - IT
+snmp-server location Serveroom
+snmp-server community public group network-operator
+</code>
+\\
+==== LLDP ====
+<code>
+feature lldp
+</code>
 \\
 ===== vPC Link Config (MLAG) =====
+Beispiel eines Nexus **C93180YC-FX3** \\
+Hier muss ein VPC Keepalive Link gesetzt werden. Dieser kann einfach 10G oder 25G sein. \\
+Danach konfiguriert man den Peer Link über 2x 100G
+\\
+\\
+==== VPC Keepalive ====
+VPC Keepalive Link über 1x 10G oder 25G
+\\
+\\
-<code ->
+Auf beiden Switches
+<code>
 feature vpc
+feature lacp
+feature interface-vlan
+feature vtp
+</code>
+\\
-vpc domain 10
+VPC Config auf Switch #1
-peer-keepalive destination <remote-node-ip> source <local-node-ip>
+<code>
-auto-recovery
+vpc doamin 1
-exit
+show vpc role
+vrf context vpc-keepalive
+interface Ethernet1/48
+  description *** VPC-PEER-KEEPALIVE ***
+  no switchport
+  vrf member vpc-keepalive
+  ip address 10.193.214.1/30
+  no shutdown
+</code>
+\\
+VPC Config auf Switch #2
+<code>
+vpc doamin 1
+show vpc role
+vrf context vpc-keepalive
+interface Ethernet1/48
+  description *** VPC-PEER-KEEPALIVE ***
+  no switchport
+  vrf member vpc-keepalive
+  ip address 10.193.214.2/30
+  no shutdown
+</code>
+\\
+Test ob sich die Switches erreichen können\\
+Ping von Switch #2 auf #1
+<code>
+ping 10.193.214.1 vrf vpc-keepalive
+</code>
+\\
+Auf Switch #1
+<code>
+vpc domain 1
+peer-keepalive destination 10.193.214.2 source 10.193.214.1 vrf vpc-keepalive
+</code>
+\\
+Auf Switch #2
+<code>
+vpc domain 1
+peer-keepalive destination 10.193.214.1 source 10.193.214.2 vrf vpc-keepalive
+</code>
+\\
+Kontrolle auf beiden Switches
+<code>
+show vpc peer-keepalive
+show vpc
+</code>
+\\
+\\
+==== VPC Peer Link ====
+Kann eingerichtet werden wenn der VPC Keepalive Link steht. \\
+VPC Peer Link über 2x 100G.\\
+\\
+Auf beiden Nodes
+<code>
 int po10
 description *** vPC PEER LINK ***
@@ Line 54: / Line 167: @@
 spanning-tree port type network
 vpc peer-link
-exit
-int eth1/49
+interface eth1/53-54
-description *** PEER LINK ***
+description *** vPC PEER-LINK Interface ***
-switchport
-switchport mode trunk
-channel-group 10 mode active
-no shutdown
-exit
-int eth1/50
-description *** PEER LINK ***
 switchport
 switchport mode trunk
@@ Line 71: / Line 175: @@
 no shutdown
 </code>
+\\
+Kontrolle auf beiden Switches
+<code>
+show vpc peer-keepalive
+show vpc
+</code>
+\\
+\\